The Simpson HSS2-SDS1.5 Galvanized Stud Shoe for 2x Studs is a Simpson Strong-Tie engineered connector built to reinforce vertical wall studs that have been notched or drilled during construction - most commonly when a plumbing waste line needs to pass through a stud. By installing over the outside of the pipe, the connector restores critical structural capacity, providing resistance in both tension and compression so the wall assembly continues to perform safely. Fabricated from 16-gauge steel with a G90 zinc galvanized finish, this stud shoe meets the exacting quality standards that engineers and contractors rely on for residential and commercial framing applications.

Key Features

• Reinforces notched or drilled studs - restores structural integrity to wall framing that has been compromised to accommodate pipes or utilities, helping maintain safe load-bearing performance.
• Installs over pipe up to 2-3/8 in. outside diameter - accommodates typical residential and commercial plumbing waste lines without requiring additional modification to the stud or pipe.
• Provides resistance in both tension and compression - addresses two distinct load directions simultaneously, giving the repaired stud broader structural support than simpler reinforcement methods.
• Flared flange design - increases the bearing area at the stud connection point, delivering greater strength and stability where the connector wraps the notched section.
• 16-gauge steel construction - a heavier gauge that contributes to the connector's ability to handle meaningful structural loads in framed wall assemblies.
• G90 zinc galvanized finish - provides an added layer of corrosion resistance, making the connector suitable for use in environments where moisture exposure is a concern.
• Includes (12) 1/4 in. x 1-1/2 in. Strong-Drive SDS Heavy-Duty Connector screws - the required fasteners ship with the connector, so installation can begin without sourcing additional hardware separately.

Why This Product

• A purpose-built solution for notched-stud repair - rather than a generic bracket or field-fabricated fix, this connector is specifically engineered and tested by Simpson Strong-Tie to address the structural loss caused by notching or drilling through a wall stud, giving builders and inspectors confidence in the repair.
• Tension and compression capacity in a single connector - many stud reinforcement approaches address only one load direction; this stud shoe is designed to provide resistance in both, making it a more complete structural solution for plumbing rough-in situations.
• Ready to install right out of the package - the included Strong-Drive SDS screws are the specified fasteners for this connector, so there is no guesswork about compatibility and no separate trip to source hardware.
• Corrosion-resistant finish for long-term performance - the G90 zinc galvanized coating helps the connector hold up over time in wall cavities where occasional moisture or humidity may be present, protecting the structural connection throughout the life of the building.

Specifications

• MPN: HSS2-SDS1.5
• Member Size: 2x
• Gauge: 16
• Coating: Zinc Galvanized, G90
• Finish: Zinc Galvanized, G90
• Install With: (12) 1/4 in. x 1-1/2 in. Strong-Drive SDS Heavy-Duty Connector screws (included)
• Width: 1-9/16 in.
• Country of Origin: United States

What's Included

Each pack contains (1) HSS2-SDS1.5 2X Stud Shoe, (12) 1/4 in. x 1-1/2 in. Strong-Drive SDS Heavy-Duty Connector screws.

Frequently Asked Questions

What is a stud shoe used for?

A stud shoe, such as the HSS2-SDS1.5, is used to reinforce vertical studs that have been notched or drilled during construction - most commonly to allow plumbing waste lines to pass through a wall stud. The connector restores structural capacity by providing resistance in both tension and compression.

What pipe outside diameter can this stud shoe accommodate?

The HSS2-SDS1.5 installs over pipe with an outside diameter of up to 2-3/8 in., making it suitable for typical residential and commercial plumbing waste line applications.

Does this stud shoe fully replace the material removed from the stud?

No. The HSS2-SDS1.5 is not a total replacement of removed material. It is designed to provide structural resistance in both tension and compression, reinforcing the stud, but it does not function as a complete substitute for the original stud material that was notched or removed.

What fasteners are required to install the HSS2-SDS1.5, and are they included?

Installation requires (12) 1/4 in. x 1-1/2 in. Strong-Drive SDS Heavy-Duty Connector screws, which are included with the connector.

Note: Product dimensions and/or Screw or Bolt holes may differ from picture. Please see item description for specifications.