The Simpson LUS210-3Z LUS ZMAX Galvanized Face-Mount Joist Hanger for Triple 2x10 by Simpson is an economical, easy-to-install face-mount connector engineered to support triple 2x10 and 2x12 lumber members in residential and commercial framing. Built from 18-gauge steel with a ZMAX galvanized finish, this hanger delivers a strong, load-rated connection for face-mount joist and rafter applications where corrosion resistance and installation efficiency both matter.

Key Features

• Patented double-shear nailing design - distributes load through two points on each joist nail, delivering greater connection strength while requiring fewer fasteners and allowing the use of all common nails for the same connection.
• Speed prongs - hold the hanger in position during installation, freeing both hands and speeding up the fastening process on the job site.
• Angled joist nailing - makes driving nails or screws easier in tight framing spaces where a straight approach is difficult.
• 18-gauge steel construction - provides a solid, load-rated connector capable of handling the demands of triple-member joist assemblies in structural framing applications.
• ZMAX galvanized coating - offers extra corrosion resistance beyond standard galvanization, making this hanger well-suited for exterior framing and treated-wood applications exposed to moisture and chemicals.
• Compatible with triple 2x10 and 2x12 lumber members - gives framers flexibility across common nominal sizes without needing a separate connector for each dimension.

Why This Product

• Fewer fasteners without sacrificing strength - the patented double-shear nailing design means each nail carries load at two shear points, so you achieve a stronger connection with a reduced fastener count compared to conventional single-shear hangers.
• Built for treated-wood and exterior conditions - ZMAX galvanization provides a higher level of corrosion protection than standard coatings, making this hanger a reliable choice for outdoor decks, exposed framing, and pressure-treated lumber assemblies where moisture resistance is critical.
• Faster installation from start to finish - speed prongs, angled joist nailing, and compatibility with common Simpson Strong-Tie fasteners (including Strong-Drive SD screws and SCN nails) reduce setup time and keep the installation moving in both new construction and renovation framing.
• Versatile fit for triple-member assemblies - acceptance of both triple 2x10 and 2x12 nominal sizes in a single connector model simplifies procurement and reduces the number of different hanger SKUs a framing crew needs to keep on hand.

Specifications

• Model Number: LUS210-3Z
• Member Size: Triple 2x10 and 2x12
• Seat Depth: 2 in.
• Width: 4-5/8 in.
• Height: 8-3/16 in.
• Gauge: 18
• Coating: ZMAX
• Finish: ZMAX
• Country of Origin: United States

Approved Applications

• Face-mount joist and rafter connections for triple 2x10 and 2x12 lumber members
• Exterior framing and treated-wood applications requiring enhanced corrosion resistance
• Common lumber framing where economical, load-rated connectors are required
• Applications where faster installation with fewer fasteners is a priority

Frequently Asked Questions

What fasteners are recommended for installing the LUS210-3Z?

Install with Simpson Strong-Tie Strong-Drive SD Connector screws: (8) #9 x 1-1/2 in. screws in the header AND (6) #9 x 2-1/2 in. screws in the joist, OR (14) 0.162 in. x 3-1/2 in. Strong-Drive SCN Smooth-Shank Connector nails (Models: SD9112, SD9212, 16DHDG).

What is the benefit of the double-shear nailing design on this hanger?

The patented double-shear nailing design distributes the load through two points on each joist nail, providing greater strength. This allows for fewer nails, faster installation, and the use of all common nails for the same connection.

Why is ZMAX galvanization important for this hanger?

ZMAX galvanization offers extra corrosion resistance, making this hanger well-suited for exterior framing and applications involving treated wood where standard galvanization may not provide adequate protection against moisture and chemical exposure.

Can the tabs on the LUS210-3Z be bent or removed to fit a specific application?

No. The tabs on the LUS210-3Z must not be bent or removed. Modifying the tabs could compromise the structural integrity and load-rated performance of the connector.

Downloads and Resources

• Face-Mount Hangers - Solid Sawn Lumber (DF / SP) Tables
• Face-Mount Hangers - Solid Sawn Lumber (SPF / HF) Tables

Note: Product dimensions and/or Screw or Bolt holes may differ from picture. Please see item description for specifications.