The Simpson LRU210Z Light Rafter U Hanger delivers an economical solution for sloped rafter-to-ridge connections in solid sawn rafter framing. Built by Simpson with an 18-gauge steel construction and ZMAX galvanized finish, this field-adjustable hanger is engineered to handle a wide range of roof pitches without the delays or guesswork of mismatched angles on the job site. Its open-profile design lets installers place the hanger before or after the rafter is set, making it a practical choice for new roof framing and retrofit projects alike - all while providing comparable or better load capacity than standard rafter hangers using fewer fasteners.

Key Features

• Field-adjustable seat that slopes up or down to 45 deg. (12:12) - eliminates mismatched angles on site so crews can dial in the correct pitch without special orders or rework
• Accommodates roof pitches from 0:12 to 14:12 - covers everything from flat to steep rooflines in a single hanger model, reducing the need to stock multiple SKUs
• For slopes greater than 45 deg. up to 49 deg. (14:12), allowable loads are 0.85 of table loads - gives installers clear, honest load guidance so structural decisions stay accurate on steep-pitch applications
• Open design allows installation before or after the rafter is in place - speeds up workflow on both new construction and retrofit jobs where access or sequencing is a constraint
• Fasteners on the face of the hanger are placed high - enables the bottom of the rafter to hang below the ridge beam, adding layout flexibility for complex roof assemblies
• Compatible with nominal 2x8, 2x10, and 2x12 rafter sizes - a single versatile hanger model serves multiple framing dimensions across a project
• Made from 18-gauge steel - provides a sturdy, consistent connection without the bulk or cost of heavier-gauge alternatives
• ZMAX galvanization offers extra corrosion resistance for exterior and treated-wood applications - protects the connection long-term in environments where standard galvanized finishes fall short

Why This Product

• One hanger, fewer headaches - the field-adjustable seat handles pitches from flat to steep (0:12 to 14:12) without requiring separate angle-specific hangers, cutting both material costs and ordering complexity
• Retrofit-friendly open design - because the hanger can be installed before or after the rafter is in place, it fits seamlessly into repair and remodel projects where traditional hangers would require dismantling existing work
• Cost-effective load performance - the LRUZ delivers comparable or better load capacity than competing rafter hangers while using fewer fasteners, which lowers both hardware costs and installation time on the job
• Built for exterior and treated-wood environments - ZMAX galvanization provides the added corrosion resistance needed for outdoor framing and pressure-treated lumber applications, helping the connection hold up over the life of the structure

Specifications

• MPN: LRU210Z
• Member Size: 2x8, 2x10, 2x12
• Gauge: 18
• Seat Width: 1-9/16 in.
• Coating/Finish: ZMAX
• Install With: 0.148 in. x 3 in. nails, 0.162 in. x 3-1/2 in. nails or #10 x 1-1/2 in. or 2-1/2 in. Strong-Drive SD screws (sold separately)
• Height: 8-3/16 in.
• Width: 1-9/16 in.
• Country of Origin: United States

Approved Applications

• Rafter-to-ridge beam connections requiring a sloped hanger
• Solid sawn rafter framing applications
• Exterior and treated-wood construction environments where corrosion resistance is required
• Retrofit framing projects where the hanger must be installed after the rafter is already in place
• New construction roof framing across a wide range of roof pitches from flat (0:12) to steep (14:12)

Frequently Asked Questions

What roof pitches does the LRU210Z accommodate?

The LRU210Z accommodates roof pitches from 0:12 to 14:12. It slopes up or down to 45 deg. (12:12). For slopes greater than 45 deg. up to 49 deg. (14:12), allowable loads are 0.85 of table loads.

Can the LRU210Z be installed after the rafter is already in place?

Yes. The LRUZ's unique open design enables the hanger to be installed either before or after the rafter is in place, making it suitable for both new construction and retrofit applications.

What fasteners should be used to install the LRU210Z?

Install with 0.148 in. x 3 in. nails, 0.162 in. x 3-1/2 in. nails, or #10 x 1-1/2 in. or 2-1/2 in. Strong-Drive SD screws.

Why is ZMAX galvanization important for this hanger?

ZMAX galvanization offers extra corrosion resistance, making the LRU210Z well-suited for exterior applications and use with treated wood where standard galvanization may not provide adequate protection.