The Simpson HTU26 Heavy Face-Mount Truss Hanger for 2x6 is a structural connector engineered by Simpson to deliver reliable load transfer beneath joists, rafters, and beams in truss framing applications. Its nail patterns are designed specifically for shallow heel heights, with full allowable loads achievable through minimum nailing at heel heights as low as 3-7/8 in. - a critical advantage in truss assemblies where heel height is constrained. Two nailing configurations give installers flexibility to match fastener placement to the demands of varying heel heights and end conditions, making this hanger a practical and performance-driven choice for residential and light commercial framing projects.

Key Features

• Nail patterns optimized for shallow heel heights - full allowable loads with minimum nailing apply at heel heights as low as 3-7/8 in., so structural performance is not compromised in tight truss applications.
• Two nailing configurations available - round holes only can be filled for standard installations, or both round and triangle holes can be filled for maximum load values, giving framers a solution adaptable to varying job conditions.
• 16-gauge steel construction - heavy-gauge material provides the rigidity and strength needed for demanding face-mount truss connections without adding unnecessary bulk.
• Zinc Galvanized G90 finish - the G90 galvanized coating delivers extra corrosion resistance, helping the hanger hold up in moisture-prone framing environments over the long term.
• Compatible with common fastener types - installs with 16d common nails and 10d x 1-1/2 in. nails, or #9 x 1-1/2 in. Strong-Drive SD Connector screws, so crews can work with fasteners they are likely already carrying on site.

Why This Product

• Built for shallow heel truss framing - the HTU26's engineered nail pattern is purpose-designed for shallow heel heights, allowing full load capacity to be achieved even where many standard hangers fall short, reducing the need for costly field modifications.
• Flexible installation for varying conditions - the ability to choose between round-hole-only or combined round and triangle hole nailing means a single hanger model can address a wider range of heel heights and end conditions on the same job site.
• Heavy-duty 16-gauge steel with corrosion-resistant G90 galvanizing - the combination of thick-gauge steel and a G90 galvanized coating means this hanger is built to perform structurally and resist degradation in the environments where truss framing hardware is routinely exposed to moisture.
• Made by Simpson, a trusted name in structural connectors - Simpson's HTU series is part of a comprehensive lineup of engineered hangers developed with documented load values and installation guidelines, giving builders and inspectors confidence in the connection.

Specifications

• Model Number: HTU26
• Brand: Simpson Strong-Tie
• Member Size: 2x6
• Gauge: 16
• Width: 1-5/8 in.
• Height: 5-7/16 in.
• Coating/Finish: Zinc Galvanized, G90
• Seat Depth: 3-9/16 in.
• Country of Origin: United States
• Install With: 16d common nails and 10d x 1-1/2 in. nails, or #9 x 1-1/2 in. Strong-Drive SD Connector screws (sold separately)

• HTU may be skewed up to 67-1/2 deg.. Contact us for Configurable Options and Special orders

Installation:

• Install with 16d common nails and 10d x 1-1/2 in. nails, or #9 x 1-1/2 in. Strong-Drive SD Connector screws
  
• Can be installed filling round holes only, or filling round and triangle holes for maximum values
• See alternate installations in Specifications

Frequently Asked Questions

What heel height can the HTU26 accommodate with full allowable loads?

The HTU26 is engineered with nail patterns specifically for shallow heel heights. Full allowable loads with minimum nailing apply to heel heights as low as 3-7/8 in., making it well-suited for truss applications where heel height is limited.

What nails or fasteners should be used to install the HTU26?

The HTU26 should be installed with 16d common nails and 10d x 1-1/2 in. nails, or #9 x 1-1/2 in. Strong-Drive SD Connector screws. Round holes only can be filled for standard loads, or both round and triangle holes can be filled for maximum values.

What gauge steel is the HTU26 made from, and what corrosion protection does it have?

The HTU26 is made from 16-gauge steel and is finished with a G90 zinc galvanized coating, providing extra corrosion resistance for demanding job site conditions.

Is there an allowance for gaps between the truss end and the carrying member?

Yes. Alternate allowable loads are provided for gaps between the end of the truss and the carrying member up to 1/2 in. max., allowing for greater construction tolerances. The maximum gap for standard allowable loads is 1/8 in. per ASTM D7147.

Note: Product dimensions and/or screw or nail holes may differ from picture. Please see item description for specifications.