The Simpson DGT Top-Flange Fire Wall Hanger is a patent-pending, load-tested connector engineered for multifamily, multilevel Type III residential construction. Carrying a two-hour fire-resistant rating tested to ASTM E814 and rated for use on both sides of the wall, this joist hanger is the first fire wall hanger designed to install with a power nailer - helping framing crews save time before drywall is hung and keeping construction projects on schedule. The innovative top-flange design accommodates two layers of 5/8 in. gypsum board slipped into place after framing is complete, eliminating rework and supporting a clean, efficient installation sequence.

Key Features

• Power nailer compatible, loads tested and code listed for 1 1/2 in. and 2 1/2 in. power-driven or hand-installed nails - gives framing crews the flexibility to use standard pneumatic nailers or hand-nail, reducing installation time and labor cost before drywall goes up.
• Two-hour fire rating applies to 2x4 or thicker walls - meets fire-resistance requirements for multifamily and multilevel residential projects, supporting code compliance with confidence.
• Innovative top-flange design for back-to-back installation on 2x6 (min.) walls - simplifies fire wall framing at shared wall assemblies without the need for custom or specialty hardware.
• Space for two layers of 5/8 in. drywall after framing is complete - the hanger stays out of the way of the gypsum board, so drywall can be slipped in cleanly without disturbing the structural connection.
• Two-hour fire-resistant rating, Intertek Design No. SST/WPCF 120-01, tested to ASTM E814 - provides a third-party verified, independently tested fire rating that satisfies inspectors and code officials on regulated job sites.
• Made from 12-gauge steel with a G90 zinc galvanized finish - heavy-gauge construction delivers the strength required for structural joist connections, while the galvanized coating provides corrosion resistance in typical construction environments.

Why This Product

• The first fire wall hanger built for the power nailer - no other fire wall hanger has been designed from the ground up to accept power-driven fasteners, which means faster installation across every floor of a multilevel framing project without sacrificing the load-tested, code-listed performance the job requires.
• A single hanger handles both sides of the fire wall - the ASTM E814-tested, two-hour fire rating applies to both sides of the wall assembly, so one product specification covers the entire fire wall detail rather than requiring separate solutions for each face.
• Drywall-ready design that protects the construction schedule - because the top-flange profile holds the framing in place and leaves the cavity open, two layers of 5/8 in. gypsum board slip into position after framing is finished, keeping drywall crews moving without waiting for structural adjustments.
• Broad size range simplifies product selection - the DGT series is offered in a wide range of sizes, reducing the risk of ordering errors and making it straightforward to match the correct hanger to the engineered wood or dimensional lumber member on the plans.

Specifications

• MPN: DGT3.62/11.88
• Brand: Simpson Strong-Tie
• Member Size: 3-1/2 in. x 11-7/8 in.
• Seat Width: 3-5/8 in.
• Height: 11-13/16 in.
• Gauge: 12
• Coating / Finish: Zinc Galvanized, G90
• Fire Rating: Two-hour, Intertek Design No. SST/WPCF 120-01
• Test Standard: ASTM E814
• Country of Origin: United States
• Installation Fasteners: Install with (6) 0.148 in. x 1-1/2 in. OR 0.148 in. x 2-1/2 in. nails in the top; (2) 0.148 in. x 1-1/2 in. nails OR (4) 0.148 in. x 2-1/2 in. nails in the face; and (6) 0.148 in. x 1-1/2 in. nails in the joist (sold separately)

Options

• Contact us for Configurable Options and Special orders

Downloads and Resources

• Two-hour Fire-Resistant rating Intertek Design No. SST/WPCF 120-01
• Specifications

Note: Product dimensions may differ from picture.